Frigidaire ovens, providing a modern kitchen experience, may encounter occasional malfunction codes that disrupt their functionality. Understanding the frequently occurring malfunction codes in Frigidaire ovens is crucial as they assist users in identifying the specific issue the oven is facing. This knowledge empowers users to swiftly and effectively resolve problems, ensuring a seamless cooking experience. Here is what you need to know about Frigidaire oven malfunction codes.
Codes Table
| Fault Code | Likely Failure Condition/Cause |
|---|---|
| F10 | Control has sensed a potential runaway oven condition. Control may have shorted relay, RTD sensor probe may have a gone bad. |
| F11 | Shorted Key: a key has been detected as pressed (for more than the debounce period) will be considered a shorted key alarm and will terminate all oven activity. |
| F12 | Bad Micro Identification. |
| F13 | Control's internal checksum may have become corrupted. |
| F14 | Misconnected keyboard cable. |
| F15 | Internal Control or Power Supply failure between Power Supply Board and EOC. Replace the display board. |
| F20 | Communication failure between EOC and ESEC system (for electric range models ONLY) |
| F26 | Communication failure with Mini Oven Control Board. (for models equipped with Bake-n-Warm ONLY) |
| F30 | Open Probe or connection. Open RTD sensor probe/ wiring problem. Note: EOC may initially display an "F10", thinking a runaway condition exists. |
| F31 | Shorted Probe or connection. Shorted RTD sensor probe / wiring problem. Note: F30 or F31 is displayed when oven is in active mode or an attempt to enter an active mode is made. |
| F90 | Maximum oven door unlock time exceeded. Door motor mechanism failure. |
| F91 | Maximum oven door unlock attempts exceeded. |
| F92 | Maximum oven door open time exceeded. |
| F93 | Maximum oven door lock time exceeded. |
| F94 | Maximum oven door lock attempts exceeded. |
| Bad Probe | The probe has not been completely inserted into the wall receptacle. Insert the probe properly into the wall receptacle. The probe is defective. Replace the probe. |
| Locked | The control has been locked. Press and hold CLEAR/OFF for about 3 seconds to unlock the control. |
| Sensor Error | When using a Sensor feature, the door was opened before steam could be detected. Do not open door until steam is sensed and time is shown counting down on display. Steam was not detected in maximum amount of time. Use Cook Time to heat for more time. |
Features and Functions
Care and Cleaning
Removing and Cleaning the Filter: To remove, slide it to the rear using the tab. Pull it down and out. To clean the grease filter, soak it and then swish it around in hot water and detergent. Don’t use ammonia or ammonia products because they will darken the metal. Light brushing can be used to remove embedded dirt. Rinse, shake and let it dry before replacing. To replace, slide the filter in the frame slot on the back of the opening. Pull up and to the front to lock into place.
Reusable Grease Filters: The metal filters trap grease released by foods on the cooktop. They also prevent flames from foods on the cooktop from damaging the inside of the microwave. For this reason, the filters must ALWAYS be in place when the hood is used. The grease filters should be cleaned once a month, or as needed.
Troubleshooting
Save time and money. Review this list first and you may not need to call for service.
| Trouble | Solution |
|---|---|
| Bad Probe | The probe has not been completely inserted into the wall receptacle. Insert the probe properly into the wall receptacle. The probe is defective. Replace the probe. |
| Locked | The control has been locked. Press and hold CLEAR/OFF for about 3 seconds to unlock the control. |
| Sensor Error | When using a Sensor feature, the door was opened before steam could be detected. Do not open door until steam is sensed and time is shown counting down on display. Steam was not detected in maximum amount of time. Use Cook Time to heat for more time. |
| Oven will not start | A fuse in your home may be blown or the circuit breaker tripped. Replace fuse or reset circuit breaker. Power surge. Unplug the microwave oven, then plug it back in. Plug not fully inserted into wall outlet. Make sure the 3-prong plug on the oven is fully inserted into wall outlet. |
| Floor of the oven is warm, even when the oven has not been used | The cooktop light is located below the oven floor. When the light is on, the heat it produces may make the oven floor get warm. This is normal. |
| Please Insert Probe | Probe has been forgotten or not inserted properly. Insert the probe properly into the wall receptacle. |
| Food amount is too large for Sensor Reheat | Sensor Reheat is for single servings of recommended foods. Use Cook Time for large amounts of food. |
| You hear an unusual, low-tone beep | You have tried to start the Reminder without a valid time of day. Start over and enter a valid time of day. You have tried to start the Auto Night Light without a valid time of day entered for the on-time and off-time. Start over and enter a valid time of day. You have tried to turn the turntable on when the probe is in use. The turntable will not operate when the probe is in use. You have tried to change the power level when it is not allowed. Many of the oven’s features are preset and cannot be changed. |
Manual Pdf
Frigidaire Over the Range Microwave Oven Use and Care Manual PDF
- Miele Robot Vacuum Cleaner Error Codes and Troubleshooting - November 15, 2024
- View All Ninja Foodi Air Fryer Error Codes List - November 15, 2024
- GE Washer and Dryer Error Codes List - November 1, 2024
