What is the error code e0 on a Daewoo washing machine?

Daewoo washing machine error code OE means that water has been unable to drain from your appliance. This can be caused by a defective drain pump, faulty wiring, a malfunctioning water level sensor, or connections to the water valve and PCB.

Daewoo Washing Machine Error Codes and Fixes

Daewoo washing machine error codes play a vital role in swiftly assessing the appliance’s condition. These codes pinpoint performance-related issues, allowing users to conduct maintenance or request technical support when necessary. Familiarity with these error codes is essential for Daewoo washing machine users.

Contents

Codes List

F1: The machine turns on but does not start and LEDs No. 1 and 2 flash ( LED model) or F1 appears on display (LCD model).
F2: The machine does not take water and LEDs. 1 and 3 flash (LED model) or F2 appears on display (LCD model).
F3: LED number 2 and 3 flash (LED model) or F3 appears on monitor (Display model).
F4: The machine does not empty, does not spin and LED 1 and 4 flash (LED model) or F4 appears on display (LCD model).
F5: LED number 2 and 4 flash (LED model) or F5 is displayed (Display model).
F6: LED number 1, 2 and 4 flash (LED model) or F6 is displayed (Display model).
IE: Water inlet error.
OE: Drain error.
UE: Unbalance error. The laundry is concentrated to one side of the drum during spin. Rearrange the laundry.
LE: Door open error.
E2: Overflow error.
E4: Leakage error. Water leaks from the tub or the hose drain. Check the leak of the tub or the hose drain. Then change the tub or the hose drain.
E5: High voltage error.
E6: EMG error.
E8: Motor error.
E9: Sensor pressure error. The water level sensor is an inferior product. Change the water level sensor.
H2: Thermistor wash error.
H4: Thermistor wash overheating error.
H5: Water temp. error.
H6: Heater wash error.
H8: Heater wash overheating error. The heater worked without the water in the tub. Check the water level and the heater wash.
lb: LGBT error. The pcb ass’y is an inferior product. Change the pcb ass’y.
PFE: Pump filter error.
B1: Motor alignment error.
B2: Motor speed control error.
B3: Low voltage error.
B4: Motor startup overloading error.

Control Panel

Troubleshooting

All repairing operations required for your machine should be carried out by our authorised service provider.If your machine requires a repair or if you cannot remove the fault by the help of the information provided as follows:

Unplug your machine.
Turn the water faucet off.

Problem	Possible Solution
The door does not open	Make sure the red pilot lamp turns off Make the special function SOAK or RINSE HOLD is not activated Push the door from the door locking side or give a slight tap and at the same time pull it to open
The is water on the floor	Make sure the red pilot lamp turns off Make the special function SOAK or RINSE HOLD is not activated Push the door from the door locking side or give a slight tap and at the same time pull it to open
The washing machine pelting in water even when it is off	Make sure the red pilot lamp turns off Make the special function SOAK or RINSE HOLD is not activated Push the door from the door locking side or give a slight tap and at the same time pull it to open
The machine vibrates noticeably	Ensure that the transportation screws have been removed during installation Ensure using the correct detergent for washing machine Make sure that the laundry is not amassed or knotted and that the spin speed is adequate for the laundry load. It so recommended that for excessive laundry load and less than half the nominal load capacity set the spin speed to low Make sure the drain pump filter is not clean. Ensure that the drain pump is squashed and that the machine dranins effectively Ensure that the machine is properly levelled on floor. It is recommeded that for any eventual feet imbalance compensation the feet must regulated and lock them in place with the locking knob ( see figure on page 10)
The machine does not turn on or start	Make sure that the power plug is inserted. Make sure there is power in the socket. Make sure that the selector switch, programme selector knob 1, is not in the OFF position.

Most problems are easily solved if you understand the cause. Check the following list for problem before calling for service. If the error mode such as IE, OE, UE were displayed on the control part, in order to solve these problem, first turn off the power of the washing machine and then turn on the power pressing Power button. If PFE error mode was displayed on the control part, in order to solve this problem, first turn off the power of the washing machine, second turn on the power pressing Power button, third press SPIN button and last press Start/Hold button.

Automatic Fault Warnings And What To Be Done

Your machine is equipped with the systems which are capable of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-checking during washing operations.

Daewoo Washing Machine Automatic Fault Warnings

Wiring Diagram

Manual Pdf

Daewoo Washing Machine Manual PDF

Author
Recent Posts

Dylan Joseph

Appliance Expert at FindErrorCode.com

FindErrorCode.com is a reputable error code provider firm. The main challenges are fault code and a problem-solving blog. We've written articles to address your concerns. Do not forget to write to us the fault codes that you cannot find. Appliance Expert contact: dylanjoseph@finderrorcode.com Call: 916-954-2677