Sharp Washing Machine Error Codes – Causes and Solutions

Sharp Corporation, formerly known as Hayakawa Metal Works, was founded in 1912. A Japanese multinational corporation that designs, manufactures, and sells electronics all over the world. With headquarters in Sakai-Ku, the company is majorly owned by Foxconn Group. While being around for decades Sharp did not get to manufacturing washing machines and ovens till 2014.

Currently, the company offers a wide range of selections on their washer and dryers and is working on introducing more cost-effective and energy-saving solutions. With a wide selection, you are finally able to control the purchase and choose a product based on your unique requirements.

Washers need to be a reliable source, but can easily give away unexpectedly. A common issue that mostly has a quick and easy fix. To help you out we have listed down some of the most common error codes for Sharp washers. Using the exact error code you can determine and even fix the issue your sharp washer is facing.

ES-U10HT Model Codes

ES-U10HT Model-Sharp Washing Machine Error Codes
ES-U10HT Model-Sharp Washing Machine Error Codes

It generates a beep when washing machine indicates abnormal display. If not connected in 10 min, it turns off automatically. Because the phenomenon may not be a fault, please check it again before sending the machine for repair. In the case of failure, please consult the maintenance department. Be sure not to disassemble and repair the machine without permission.

Error CodePossible Failure and Solution
E1Low flow at the faucet. Inclease water supply, press START / PAUSE key.
The faucet is closed. Turn the faucet on, press START/PAUSE key.
Water inlet filter net is blocked. Clean filter net, press START/PAUSE key
E2Top cover is opened as the reservation course starts. Close top cover.
Top cover is not closed during spin drying. Close top cover.
E3The drain position is relatively high. Adjust drain hose properly, press START/PAUSE key
The end of drain hose is blocked. Clean drain hose, press START/PAUSE key.
Drain hose is folded/ crumpled/tied. Clean drain hose, press START/PAUSE key.
E4Washing machine inclines or is shaky. Washing machine place the horizontally with adjusting the foots
The clothing is lopsided. Distribute the clothing evenly
E5Draining position is relatively high. Lower down the drain hose, press START/PAUSE button.
Drainage hose is frozen or blocked. Defreeze/unblock drainage hose, press START/PAUSE button.
Drainage hose is bent, squeezed, tangled. Smooth out drainage hose, press START/PAUSE button.
E7Lid do not close when safety lock is on. Close the lid in 10s and program will resume itself; if lid is still open after 10s, machine will start draining. To resume, deselect SAFETY LOCK mode.
C2Water level sensor shows an abnormal level. Water level sensor shows an abnormal level.
U9Top cover opened in the situation of CHILD LOCK. Turn the power off, and take it from the top. CHILD LOCK is not released, unless you reset it manually
EC6Clutch mechanism failure, Main board defective, Wiring/connection problem.

Model ES-GFC Codes

Model ES-GFC Sharp Washing Machine Error Codes
Model ES-GFC Sharp Washing Machine Error Codes

Your Washing Machine is equipped with a built-in fault detection system which shows any fault details on the electronic display. The most common failure codes are shown below. If your machine displays a code not shown, or if the problem persists after you have taken corrective action, consult the Sharp helpdesk.

Error CodePossible FailureSolution
E01The door is not shut properlyShut the door properly so that you hear the click
E02The water level in your machine may be low, or the water pressure may be lowCheck that the cold water tap is fully turned on
E03The pump has failed, or the pump filter is obstructedCheck that the cold water tap is fully turned on
E04There is an excessive amount of water in your Washing MachineYour Washing Machine will automatically drain the water. Turn your Washing Machine off, unplug it and contact the Sharp helpdesk
There is no water supply or the mains water pressure is lowCheck mains water supply is on and has sufficient pressure. If the mains supply has been cut off, switch the control dial to Stop and re-select the programme once the supply has been restored.
Faulty pump or clogged pump filterThe pump filter may be clogged. Check and clean if necessary

Control Panel

Sharp Washing Machine Control Panel Overview
Sharp Washing Machine Control Panel Overview

Troubleshooting

If your Washing Machine is not operating as expected, you may find a simple solution listed in the table below. If your Washing Machine is not working and one or more of the indicator lights are flashing, this means that the automatic error detection system has diagnosed a fault.

TroubleCause
Your Washing Machine does not operateIt is switched off at the mains. Check that your Washing Machine is plugged in and turned on at the mains.
Your Washing Machine does not receive waterThe cold water supply tap is off. Check that the cold water supply tap is fully turned on.
Your Washing Machine does not receive waterThe water inlet filters are blocked. Clean the water inlet filters.
Your Washing Machine is not draining water. The drain hose is bent, twisted, kinked or trapped. Check the drain hose and straighten out any kinks, twists or bends.
Your Washing Machine is vibratingThe feet of your machine are not correctly adjusted. Adjust the feet.
There is excessive foam in the detergent drawerToo much detergent has been used. Press the Start/Pause button. To stop the foam, dilute one tablespoon of softener into 1/2 litre of water and pour into the detergent drawer. Press the Start/Pause button after 5-10 mins.
There is excessive foam in the detergent drawerThe wrong detergent has been used. Only use detergents produced for automatic Washing Machines.
The washing result is not as expectedYour laundry is too dirty for the programme you’ve selected. Use the information on pages 25 to 30 to select the most appropriate programme.
The water from the machine is drained as soon as it is filledThe end of the water drain hose may be too low. Check that the drain hose is at a suitable height.
The spin cycle does not take placeThe in-built sensor has prevented your Washing Machine from operating with an out-of-balance load. Avoid small wash loads containing items that could become heavy through water absorption.

Cleaning

Filters

Water Inlet Filters:

Water inlet filters prevent dirt and foreign materials from entering your machine. It is recommended that these filters are cleaned when your machine is unable to receive sufficient water, although your water supply is on and the tap is open.

Sharp Washer Water Filter
Sharp Washer Water Filter

To clean the water inlet filters:

  1. Unscrew the water inlet hose from the Washing Machine by turning the hose anticlockwise and gently pulling.
  2. To remove the water inlet filter from the water inlet valve, use a pair of long-nosed pliers to gently pull on the plastic bar in the filter.
  3. Clean the filter thoroughly with a soft brush, wash with soapy water and rinse thoroughly.
  4. Re-insert the filter by gently pushing it back into place.

A second water inlet filter is located in the tap end of the water inlet hose. To remove the second water inlet filter:

  1. Use a pair of long-nosed pliers to gently pull on the plastic bar in the filter.
  2. Clean the filter thoroughly with a soft brush and wash with soapy water and rinse thoroughly.
  3. Re-insert the filter by gently pushing it back into place.

Pump Filter:

The pump filter system in your Washing Machine prolongs the life of the pump by preventing lint from entering your machine. We recommend that you clean the pump filter every 2-3 months. The pump filter is located behind the cover on the front-lower right corner.

Sharp Washer Pump Filter
Sharp Washer Pump Filter

CAUTION: The water in the pump may be hot, wait for it cool before carrying out any cleaning or maintenance.

Cleaning the Pump Filter:

  1. Before opening the filter cover, place a container under the filter cover to collect any water left in the machine. Pull the top of the cover forwards using the finger groove, until the pump filter is fully exposed
  2. Loosen the filter by turning anti-clockwise and remove by pulling. Wait for the water to drain.
  3. Remove any foreign materials from the filter with a soft brush.
  4. Move the pump by hand to check that it rotates freely.
  5. Clean the pump with a soft brush.

After Cleaning:

  1. Re-fit the filter by inserting it and turning clockwise.
  2. Close the filter cover.

What is the error code E01 on a Sharp washing machine?

The machine has detected that the door is not closed properly or the door can't lock.

What is E02 on Sharp washing machine?

The machine has detected that the water pressure is too low.

Manual Pdf

Sharp Washing Machine Manual PDF

All Washing Machine Brands Error Code List

Dylan Joseph
Follow us
Share on:

26 thoughts on “Sharp Washing Machine Error Codes – Causes and Solutions”

Leave a Comment