Aeg Oven Error Codes – How to Easily Fix Them

AEG oven error codes serve as a crucial resource for understanding appliance issues. Each code represents a specific error, and accurate diagnosis is key to swift resolution. These codes guide users in identifying problems, enabling an effective repair process to commence.

Codes List

If the oven is not working correctly, please carry out the following checks before contacting yourlocal AEG Service Force Centre.

Error CodesMeaning
C2You want to start the Pyrolysis or Defrost function, butyou did not remove the foodsensor plug from the socket. Remove the food sensorplug from the socket.
C3The cleaning function doesnot operate. You did not fullyclose the door, or the doorlock is defective. Fully close the door.
C4The Plus Steam is pressed. Press the Plus Steam again.
F1Door is not closed properly. Close the door properly andstart the pyroluxe again. If displayed again, please contact your local Service Force Centre.
F2Door not properly closed or door lock defective. Close door properly; Turn the appliance off and on again via the house fuse orthe safety switch in the fusebox; If displayed again, please contact the Customer Care Department.
F3Fault in the electronics
F4Fault in the electronics
F5Temperature exceeded
F6Temperature exceeded
F8Fault in the electronics. Switch off the appliance via the house fuse or the safety switch in the fuse box and switch it on again.
F11The meat probe has shortcircuited or the plug of themeat probe is not firmly in po-sition in the socket. Insert the plug of the meatprobe as far as it will go intothe socket on the side wall ofthe oven.
F102Possible cause: 1- You did not fully close thedoor. 2- The door lock is defective. Remedy: 1- Fully close the door. 2- Deactivate the oven withthe house fuse or the safety switch in the fusebox and activate it again. 3- If the display shows"F102" again, contact theCustomer Care Department.
F111The plug of the core tem-perature sensor is not cor-rectly installed into the socket. Put the plug of the core temperature sensor as far aspossible into the socket.
12.00Set the time of day (see chapter "Toset the correct time of day")
E001Temperature outside of thepermissible range. Please contact customer service.
E020Door is not closed properly. Close the door properly and start the pyrolysisfunction again.
E021Temperature outside of thepermissible range. Please contact customer service.

Control Panel Meaning

Aeg Oven Control Panel Meaning
Aeg Oven Control Panel Meaning

Cleaning The Oven Door

The following instructions explain how to disassemble the oven door as it is supplied by the Manufacturer.

If your oven door has been reversed, please note that the references to the right or left side have to be switched.

AEG Oven - Cleaning the oven door
AEG Oven – Cleaning the oven door
  • Figure 28. With the right hand, hold the aluminium perforated grid (“A”) while with the left hand pull off the support “B” of the inner glasses. Push the support towards the right to release it and then lift it up.
  • Figure 29. Remove the aluminium perforate grid “A” from support “C”.
  • Figure 30. Hold firmly the inner glass “D” with the left hand and pull the support “C” off from its original position. Make sure that glass “D” is firmly held to avoid it from falling.
  • Figure 31. Hold the inner glass “D” tightly with both hands and remove it from its original position by sliding it upwards.
  • Figure 32. Tightly hold with both hands the second inner glass “E” and remove it from its original position also by sliding it upwards.

After removing the inner glass, clean the oven door and the glasses. We recommend to clean the oven door using only a wet sponge and dry it after cleaning with a soft cloth. Never use steel wool, acids or abrasive products as they can damage the surface.

Symbol Status Bar and Button Meaning

AEG Oven Symbol Status Bar and Button Meaning
AEG Oven Symbol Status Bar and Button Meaning

Troubleshooting

AEG Oven Troubleshooting
AEG Oven Troubleshooting

If the oven is not working correctly, please carry out the following checks before contacting your local AEG-Electrolux Service Force Centre.

TroubleSolution
The oven does not come on.1. Touch the OVEN ON control, then select a cooking function. 2. Check the fuse and ensure the socket switch or the switch from the mains supply to the oven are ON.
The oven light does not come on.1. Switch on the oven using touch control . 2. Check the light bulb, and replace it if necessary.
It takes too long to finish the dishes, or they are cooked too fast.1. The temperature may need adjusting. 2. Refer to the cooking function sections and to any cooking chart provided.
Steam and condensation settle on the food and the oven cavity.Leave dishes inside the oven no longer than 15-20 minutes after the cooking is completed.
The electronic programmer does not work.Check the instructions for the electronic programmer.
The oven fan is noisy.Check that shelves and bakeware are not vibrating in contact with the oven back panel.
Error code, for example "POBERR 80" appears on the control panel.Take note of the error code and contact an authorised Service Centre.

If after all these checks, your oven still does not operate correctly, contact your local AEG-Electrolux Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.

Manual

AEG Built-In Electric Oven User Manual PDF

Dylan Joseph
Follow us
Latest posts by Dylan Joseph (see all)

Leave a Comment