The error codes for Amica washing machines provide crucial information for users, addressing issues that can impact the appliance’s functionality. These codes assist users in swiftly identifying problems, enabling efficient utilization of the machine.
Codes List
When an warning is displayed, refer to the following and take the appropriate action.
| Error Codes | Problem |
|---|---|
| E01 | No feedback signal from door interlock. After 15 seconds the E01 code is displayed and the wash programme is terminated. Washing machine door open. Faulty interlock. The door lock mechanism does not shift the interlock sensor far enough. |
| E02 | Filling time longer than 2 minutes The “Ready” LED flashes during the wash (which is not terminated). After the washing is completed the E02 error code is displayed. Further fillings above the pressure controller level are blocked. Low mains water pressure. Partia||y blocked inlet hose or valves. |
| E04 | 4 “Overfill” signal from pressure controller. The E04 error code is displayed, the pump is switched on and the wash programme is terminated.After1.5 minutes from sending of the “Reservoir empty” signal by the pressure controller the pump is switched off. If water is subsequently detected while the E04 error is indicated, the pump is restarted. So|enoid valves locked in the “Open” position. Large fluctuations in water pressure during the wash cycle. Wash cycle starts with closed water inlet which is then opened during the wash. Faulty pressure controller. |
| E05 | No signal from pressure controller 10 minutes after filling starts. The E05 error code is displayed and the wash programme is terminated. No water supply. Very low mains water pressure. Faulty solenoid valve. Faulty pressure controller. Control valve (washing machines with AquaSpray) locked in the “off" position E03. Water discharge time longer than 1.5 minutes.The “Ready” LED flashes during the wash (which is not terminated). The next spin cycle after discharging the water is restricted to 400 rpm. Partia||y blocked pump filter. Partia||y blocked discharge hose. |
| E06 | No “empty” signal from pressure controller 10 minutes after water discharging starts The E06 error code is displayed and the wash programme is terminated.Blocked pump.Blocked discharge hose. Control valve locked in the “on" position. Faulty pressure controller. |
| E07 | Signal (open contacts) from the floating sensor — water at the bottom of the drum. The E07 error code is displayed and the wash programme is terminated. The pump is switched on and then switched off 1,5 minutes after the “Reservoir empty" signal is sent. Water leak from the bathtub or hoses. Faulty sensor. |
| E08 | Input voltage outside the range of 160-253V, 50/60Hz. The E08 error code is displayed, washing cannot be started. After resetting, the error is indicated again if the cause is not rectified. Incorrect mains voltage. |
| E10 | Water injecting problem while washing. Check if the water pressure is too low Straighten the water pipe Check if the inlet valve filter is blocked. |
| E11 | Malfunction of the door interlock triac. After 2 seconds the E11 error code is displayed and the wash programme is terminated. Faulty electronic circuit board. |
| E12 | Water overflow. Restart the washer |
| E21 | Motor blocked: voltage is fed to the motor but there is no signal from the rate generator. The E21 error code is displayed and the wash programme is terminated. Faulty motor (rate generator, thermal switch or winding). Motor connection block removed. Therma| switch open clue to motor overheating. |
| E21 | Overtime water draining. Check if the drain hose is blocked. |
| E22 | Motor triac shorted — there is a signal from the rate generator even though no power is supplied to the motor. The E22 error code is displayed and the wash programme is terminated. Faulty electronic circuits (the error may occasionally be caused by a heavily unbalanced load such as a blanket or dressing gown) |
| E30 | Door is not closed properly. Restart after the door is closed Check if the clothes is stuck. |
| E31 | Temperature sensor shorted The wash programme is not terminated and after its completion the E31 error code is displayed. Faulty temperature sensor. |
| E32 | Temperature sensor open The wash programme is not terminated and after its completion the E32 error code is displayed. Faulty temperature sensor. |
| E42 | Time to unlock the door of more than 120 s.The error occurs at the end of the washing, if after the washing the door is not unlocked within 2 minutes. The washing machine shows E42 error and another cycle cannot be started before the error signal is reset. door lock damaged. door is locked mechanically. |
| E51 | Incorrect data in program's memory. Displayed as error code, wasching machine start inoperable. Programmer damaged ( processor). |
| E52 | Incorrect data in configuration's memory Displayed as error code, wasching machine start inoperable. Programmer damaged ( processor). |
| E53 | Input circuit EMC errors Displayed as error code, washing machine start inoperable. Programmer damaged ( processor) |
| E54 | Autotest's errors Displayed as error code, wasching machine start inoperable. Programmer damaged;damaged circuit NTC. |
Display and Control Panel
The Fault Indicator Lights
The washing machine indicates error codes to help locate minor operating faults and identify their cause. An error is indicated by LEDs on the control panel [Ready/ Start/Pause]. The appliance interrupts operation upon encountering an error.
Troubleshooting
The start of the appliance does not work or it stops during operation. First try to find a solution to the problem, If not, contact the service centre.
Description: Washing machine cannot start up
Reason: Door is not closed properly
Solution: Restart after the door is closed Check if the clothes is stuck
Description: Door can’t be opened
Reason: Washer’s safety protection design is working
Solution: Disconnect the power, restart the product
Description: Water leakage
Reason: The connection between inlet pipe or outlet hose is not tight
Solution: Check and fasten water pipes. Clean up outlet hose
Description: Indicator or display does not light
Reason: Disconnect the power PC board or harness has connection problem
Solution: Check if the power is shut down and the power plug is connected correctly
Manual
Amica Washing Machine Manual PDF
- Smeg Washing Machine Error Codes List - December 15, 2024
- Miele Dishwasher Error Codes List and Solutions - December 15, 2024
- Beko Refrigerator Error Codes and Troubleshooting - November 30, 2024
