Blomberg dishwasher error codes provide users with a valuable guide. These codes enable you to quickly identify issues with your machine. Detecting malfunctions can extend the appliance’s lifespan and minimize repair costs. In this article, we will delve into Blomberg dishwasher error codes in detail.
Codes List
| Error | Solution |
|---|---|
| E01 | No feedback signal from door interlock. After 15 seconds the E01 code is displayed and the wash programme is terminated. |
| E02 | 2 Filling time longer than 2 minutes The “Ready” LED flashes during the wash (which is not terminated). After the washing is completed the E02 error code is displayed. Further fillings above the pressure controller level are blocked. - Low mains water pressure -Partia||y blocked inlet hose or valves . |
| 4th program led | 3 Way Valve Position Error. Possible Causes: a. Malfunction of 3W Valve b. Disconnection on the lines between the electronics and the 3W Valve |
| 3rd Program Led | NTC Fault. At the Heating step, if NTC resistance is measured as open / short circuit or beyond the specified resistance values, then NTC fault can be detected. Possible Causes: a. Malfunction of NTC b. Crack on the connection lines between electronics and NTC |
| 3rd Program Led | Heating Fault. Possible Causes: a. Malfunction of Heater b. Crack on the connection lines between electronics and heater c. Malfunction of RL1 relay on the electronic board d. Too less water inside the machine |
| 2rd Program Led | No Water and Counter Fault . Possible Causes: a. Malfunction of Water Inlet Valve b. Malfunction of Water Counter c. Crack on the connection lines between the electronics and water inlet valve d. Crack on the connection lines between the electronics and water counter |
| 1 st Program Led | Uninterruptible Water Inlet Error. Possible Causes: a. Malfunction of Water-Inlet Valve (stuck as open) b. Malfunction of T7 triac on the electronic board |
| Machine does not start | Power cable is unplugged. >>> Check if the power cable is plugged in. |
| Dishes are not washed clean | Filters are clogged. >>> Check if the filter system is clean. Clean the filter system regularly as illustrated in section “Cleaning and Care”. |
| Dishes are not dry at the end of cycle | Dishes are not placed orderly in the machine. >>> Place your dishes in a way that no water will accumulate in them. |
| Tea, cafe or lipstick stains remain on dishes. | Selected programme is unsuitable. >>> Select a programme with a higher temperature and cycle time. |
| Lime traces remain on dishes and glassware gains a misty appearance | Rinse aid is not sufficient. >>> Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine. |
| There is a different odour in the machine | Filters are clogged. >>> Check if the filter system is clean. Clean the filter system regularly as illustrated in section “Cleaning and Care”. |
| Rust, discoloration or surface deterioration occurs on dishes | Salt leakage exists. >>> Salt may cause deterioration and oxidation on metal surfaces. Pay attention not to spill salt around the salt filling hole while adding salt. Make sure that the salt reservoir lid is tightly closed after finishing the filling process. Run the prewash programme to remove the salt that spilled inside the machine. Since the salt granules that will remain under the lid will dissolve during prewash, causing the lid loosen, check the lid once again at the end of the programme. |
| Detergent remains in detergent dispenser. | Detergent dispenser was damp when adding detergent. >>> Make sure that the detergent dispenser is dried well prior to filling it with detergent. |
Draın Hose, Water Inlet Valve, And Clıp Box
To render services to these components, the operators should work on the backside of the machine. The concrete sheet should be removed. The hose holder is taken out by turning as it is seen in the picture.
Operating The Dishwasher
Cleaning The Hose Filter
Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation (such as sand, dirt, rust, etc.) can be prevented by means of the filter attached to the water inlet hose. Check the filter and the hose regularly and clean them if necessary.
- Turn off the tap and remove the hose.
- After taking out the filter, clean it under running tap water.
- Place the cleaned filter back to its seat in the hose.
- Install the hose to tap.
Cleaning The Filters
Clean the filters at least once a week in order for the machine operates efficiently. Check if food residues are left on the filters. If there are food residues on filters, take them out and clean well under running water.
- Turn the micro filter (1) and coarse filter (2) assembly counterclockwise and pull it out from its seating (A)
- Pull out the metal / plastic filter (3) from the seating (C).
- Press the two pawls on the coarse filter inwards and separate the coarse filter from the assembly (B).
- Clean all three filters under tap water by means of a brush.
- Replace the metal/plastic filter.
- Place the coarse filter into the microfilter. Make sure that it is properly seated. Turn the coarse filter clockwise until a “click” sound is heard.
Troubleshooting
Machine does not start.
- Power cable is unplugged. Check if the power cable is plugged in.
- Fuse is blown. Check the fuses in your house.
- Water is cut. Make sure that the water inlet tap is open.
- Door of the machine is open. Make sure that you have closed the door of the machine.
- On / Off button is not pressed. Make sure that you have turned on the machine by pressing the On / Off button.
Dishes are not washed clean
- Dishes are not placed orderly in the machine. Load the dishes as described in the user manual.
- Selected programme is unsuitable. Select a programme with a higher temperature and cycle time.
- Impellers are stuck. Prior to starting the programme, turn the lower and upper impellers by hand to make sure that they rotate freely.
- Impeller holes are clogged. Lower and upper impeller holes might be clogged with food remnants such as lemon pips.
- Filters are installed incorrectly. Check the filter system and make sure that it is installed correctly.
Dishes are not dry at the end of cycle
- Dishes are not placed orderly in the machine. Place your dishes in a way that no water will accumulate in them.
- Rinse aid is not sufficient. Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine.
- Selected programme is unsuitable. Since rinsing temperature is low at programmes with short duration, drying performance will also be low. Select programmes with longer duration for a higher drying performance.
Tea, cafe or lipstick stains remain on dishes.
- Selected programme is unsuitable. Select a programme with a higher temperature and cycle time.
- Surface quality of the kitchen utensils is deteriorated. Tea and cafe stains or other dye spots may not be cleaned in dishwasher when they have penetrated in deteriorated surfaces. Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well. It is not recommended to wash such kitchen utensils in dishwasher.
Lime traces remain on dishes and glassware gains a misty appearance
- Rinse aid is not sufficient. Check the rinse aid indicator and add rinse aid if necessary. Increase the rinse aid setting if there is enough amount of rinse aid in the machine.
- Water hardness setting is low or salt level is insufficient. Measure the hardness of the supply water appropriately and check the water hardness setting.
Manual
Blomberg Dishwasher Manual PDF
Appliance Expert at FindErrorCode.com
FindErrorCode.com is a reputable error code provider firm. The main challenges are fault code and a problem-solving blog. We've written articles to address your concerns. Do not forget to write to us the fault codes that you cannot find. Appliance Expert contact: dylanjoseph@finderrorcode.com Call: 916-954-2677
Latest posts by Dylan Joseph (see all)
- Smeg Washing Machine Error Codes List - December 15, 2024
- Miele Dishwasher Error Codes List and Solutions - December 15, 2024
- Beko Refrigerator Error Codes and Troubleshooting - November 30, 2024
