Below is a list of some of the possible malfunctions. To help you out we have listed down some of the most common error codes for Miele Washing Machine. The below are common fault diagnosis and elimination methods. For other faults, please contact customer service. Do not forget to write to us the fault codes that you cannot find.
Error Code | Possible Causes |
---|---|
F01 | Water/heating NTC or leads short-circuited |
F02 | Water/heating NTC or leads open-circuited |
F11 | Drainage fault |
F12 | Water intake fault at start of step |
F13 | Water intake fault: Heater pressure switch |
F14 | Water intake fault: Heater pressure switch |
F15 | Water intake fault: Hot water |
F24 | Heater relay contact |
F25 | Desired temperature fault |
F26 | Boiling protection |
F40 | Electronic fault |
F42 | Line frequency registration fault |
F47 | Mains frequency registration fault |
F51 | Heater pressure switch |
F52 | Heater pressure switch has reset during heating |
F53 | Speed sensor fault |
F63 | Slide shutter fault |
F67 | Circulation pump speed to slow |
F68 | Circulation pump operation after switch off |
F69 | Circulation pump blocked |
F70 | Float switch fault |
F84 | Slide shutter positioning fault |
F85 | Slide shutter signal change fault |
F86 | Salt container lid contact fault |
F87 | Sensor softener fault |
F88 | Turbidity sensor fault |
F91 | Load size registration inactive |

Troubleshooting
An error indicator light lights up in the control panel and the programme was cancelled.
Display: The fault indicator light ”tap” lights up, F and 10 appear alternately in the time display and the buzzer sounds.
Possible Causes and remedy:
The water inlet is blocked or restricted.
- Check whether the tap is turned on properly.
- Check whether the inlet hose is kinked.
- Check whether there is sufficient water pressure.
The filter in the water inlet is blocked.
- Clean the filter.
Display: The fault indicator light ”tap” lights up, F and 11 appear alternately in the time display and the buzzer sounds.
Possible Causes and remedy: The water outlet is blocked or restricted. The drain hose has been fixed too high.
- Clean the drain filter and the pump.
- The maximum drain height is 1 m.
Display: The fault indicator light ”tap” lights up, F and 138 appear alternately in the time display and the buzzer sounds.
Possible Causes and remedy: The water protection system has reacted.
- Turn off the tap.
- Call Miele.

Display: F and XXX alternately appear in the time display and the buzzer sounds.
Possible Causes and remedy: There is a fault.
- Disconnect the washing machine from the mains electricity supply, either by switching it off at the wall socket and withdrawing the plug, or by disconnecting it at the circuit breaker.
- Wait at least 2 minutes before reconnecting the washing machine to the mains electricity supply.
- Then switch the washing machine on again.
- Restart the programme. If the fault message appears again, contact Miele.
During the programme, a symbol appears in the time display
Display: -0- lights up
Possible Causes and remedy:
The programme selector was moved to a different position after the programme had started.
- Turn the programme selector back to the original position.
The programme has been interrupted.
- Open the door.
- Close the door.
At the end of a programme, an indicator light lights up on the control panel
Display: The indicator light 0 lights up.
Possible Causes and remedy: Excessive foam has built up during washing.
- Use less detergent next time and follow the manufacturer’s instructions on dosage given on the packaging.
Display: The indicator light + lights up.
Possible Causes and remedy: A programme using a temperature above 60°C has not been run for a long period of time.
- In order to prevent bacteria and unpleasant odours building up in the machine, run the Cottons 90°C programme using Miele Dishwasher and Washing Machine Cleaner or powder detergent.
General problems with the washing machine
Display: The washing machine smells.
Possible Causes and remedy:
The + indicator light was ignored. A programme using a temperature above 60°C has not been run for a long period of time.
- In order to prevent bacteria and unpleasant odours building up in the machine, run the Cottons 90°C programme using Miele dishwasher and washing machine cleaner or powder detergent.
The detergent dispenser drawer was left closed after washing.
- Leave the detergent dispenser drawer slightly open to allow it to dry.
Display: Large amounts of detergent residue remain in the detergent dispenser drawer.
Possible Causes and remedy:
The water pressure is too low.
- Clean the filter in the water inlet.
- It may be useful to select the Water plus Extra option.
Powder detergent used with water softeners can become sticky.
- Clean the detergent dispenser drawer and in future add washing powder and then add the water softener.
Display: At the end of the programme there is still liquid in the capsule.
Possible Causes and remedy:
The small pipe in the detergent dispenser drawer onto which the capsule is placed is blocked.
- Clean the small pipe
This is not a fault.
- For technical reasons, a small amount of water will remain in the capsule.
Display: After the programme is cancelled, flashing bars ” I_I..I_I..I_I…” appear in the time display.
Possible Causes and remedy: For safety reasons, the door cannot be opened if the suds temperature is higher than 55°C.
- Wait until the temperature in the drum has decreased and the bars have stopped flashing in the display.
Display: F and 35 alternately appear in the time display.
Possible Causes and remedy: The door lock has jammed.
- Call Miele.
QA
How do I reset my Miele washer error code?
Turn your washing machine off for around 15 to 20 seconds and then turn it back on and select another washing program.
How to fix miele w1 washer red cross symbol?
Lights up if excess detergent was used.
Miele Washing Machine Manual W 1714 PDF 1
Miele Washing Machine Manual PDF 2
Miele Washing Machine Manual PDF 3
My Miele wash mashing Everything working when I started each program machine stops and I se please close the doors everything freez and it’s takes while for unlocking doors when I switch again I have same problem again i can’t use my wash mashing I need resetting and again again again than doors it’s open programs running but if I starting washing the problem started again and all system not working I can open doors only manually